MIL-STD-2193 Ship Hydraulic System ComponentsThis standard provides design, construction, and testing requirements that are common to most components used in ship hydraulic power transmission and control systems. This standard does not establish configuration requirements, pressure, flow, or performance requirements for any specific component.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23

MIL-STD-2193C(SH)

SAE-ARP1234                -        Gland Design, Elastomeric 0-Ring Seals, Static Axial, Without Back-Up

Rings

SAE-AS1290                   -        Graphic Symbols for Aircraft Hydraulic and Pneumatic Systems

SAE-AS3209                   -        Packing, Preformed - AMS 7276, 0-Ring

SAE-AS3581                   -        Packing, Preformed - 0-Ring Seal AMS 7259

SAE-AS4716                   -        Gland Design, 0-Ring and 0ther Elastomeric Seals

SAE-AS5169                   -        Fitting, Port Plug and Bleeder

SAE-AS5781                   -        Retainers (Backup Rings), Hydraulic and Pneumatic, Polytetrafluoroethylene Resin, Single Turn, Scarf-Cut, for Use in AS4716 Glands

SAE-AS5782                   -        Retainers (Backup Rings), Hydraulic and Pneumatic, Polytetrafluoroethylene Resin, Solid, Un-Cut, for Use in AS4716 Glands

SAE-AS5857                   -        Gland Design, 0-Ring and 0ther Elastomeric Seals, Static Applications

SAE-AS5860                   -        Retainers, (Back-Up Rings), Hydraulic and Pneumatic, Polytetrafluoroethylene Resin, Single Turn, Static Gland

SAE-AS5861                   -        Retainers, (Back-Up Rings), Hydraulic and Pneumatic, Polytetrafluoroethylene Resin, Solid, Static Gland

SAE-AS8791                   -        Hydraulic and Pnuematic Retainers (Back-Up Rings), Polytetrafluoroethylene (PTFE) Resin

SAE-J429                         -        Mechanical and Material Requirements For Externally Threaded

Fasteners

SAE-J518                         -        Hydraulic Flanged Tube, Pipe, and Hose Connections, Four-Bolt Split

Flange Type

SAE-J995                         -        Mechanical and Material Requirements for Steel Nuts

SAE-J1926/1                   -        Connections for General Use and Fluid Power - Ports and Stud Ends with

ASME B1.1 Threads and 0-Ring Sealing - Part 1:  Threaded Port with

0-Ring Seal in Truncated Housing

SAE-J1926/2                   -        Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and 0-Ring Sealing - Part 2: Heavy-Duty (S Series) Stud Ends

SAE-J1926/3                   -        Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and 0-Ring Sealing - Part 3: Light-Duty (L Series) Stud Ends

SAE-J2655                       -        Fastener Part Standard-Washers and Lock Washers (Inch Dimensioned) SAE-J24714                     -        Fluid Systems--Connector Tubes--General Specification and Part

Standard

(Copies of these documents are available from SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA  15096-0001 or online at www.sae.org.)

2.4   0rder of precedence.   Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence.  Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

5